Wednesday, August 28, 2013

DIY Retaining Wall & Landscaping

It's been four years since my parents first moved into this adorable yellow house.
But, in four years... NO LANDSCAPING has been done in the front yard.


So, this summer my dad and I decided to change that... by tackling another DIY project!


We decided to do a "two-tiered" retaining wall.


First up...
We had to move the sprinkler heads away from the house.
We did this by digging down to the hose, trimming it, then moving the head farther out.
When you're done, cover the hose back up with dirt.


(You can see in this photo just how FAR we had to dig to move the sprinkler heads.)


Next...
We measured how big we wanted the retaining wall to be.
We used string line and wooden stakes to mark the height and length of each level.
(Remember, we decided to do TWO levels.)


Then...
We dug an outline in the dirt with a shovel.
You want to dig down at least four inches deeper than where your first row of block is going to be.


Add paver base on top of the dirt... and pack it down.
Your paver base needs to be LEVEL - since it's the base for your block.
(You can also add sand to help the blocks level out.)



Next...
Take a hammer and knock the back lip off each retaining wall block that 
will be used for your BOTTOM ROW.
Start at the edge, and work your way across the lip.


Notice how the lip comes off?
It's pretty easy.


BUT...
Remember - you only want the lip OFF for the BOTTOM row
You'll leave it on ALL the other rows.

The lip will help position your block - and hold your wall in place.


Then...
Start laying your first row.
Make sure the blocks are LEVEL!!!
Use a rubber mallet or dead blow hammer to help set the blocks.
(You may need to add or remove some paver base as you go along.)




Reminder...
As you're putting the blocks in place, make sure to stagger the block's joints!
(You don't want the joints to form a straight line up and down on the wall.)


Once the wall is built...
It's time to put on your cap blocks!
(These aren't necessary... but they do finish off the wall... and make it look nicer.)
They're held in place with retaining wall adhesive.
You just squirt a couple lines on the bottom of each block.


Then...
Get some landscape fabric.
You'll need this for the backside of your wall.

(This is a photo of my baby brother helping us out!)


Drape the fabric all along the backside of the wall from TOP to BOTTOM...


... and back-fill with pea gravel for drainage.
You'll need about 2-3 inches wide (of pea gravel) all along your wall.

(Unfortunately I don't have a picture of us pouring the pea gravel along the fabric. Sorry!!!)


As you're pouring the pea gravel... put dirt along side it. 
Fill the dirt all the way to the top.


Once the dirt is in... trim off the excess fabric.


Add a couple inches of compost to the dirt... and till it.
This will help your flowers and bushes grow.


Whew! 
Finally done with the wall!!!


Now that the wall is done...
It's time to start planting!


First...
We planted the bushes.
Ten total.


1.) We purchased six Spirea bushes...


... which have flowers in this pretty pink color.


2.) We also got a Rose of Sharon bush.
(My dad's favorite.)



It's a light shade of pink.


3.) And we purchased three hydrangea bushes...


... my favorite!


LOVE these!


Once the bushes were planted...
We draped more landscape fabric over the entire area.


We cut holes for the bushes...


... and secured the fabric in place with homemade stakes. 



We made our stakes by using electric fence wire.
But, you can EASILY buy ground stakes at any home improvement store.


TIME TO PLANT THE FLOWERS!


We stuck with three types of flowers:

1.) Coral Bells 
These came in another shade of pink.


2.) Hardy Mums 
These come in ALL sorts of colors - but we chose pink and red.


3.) Creeping Raspberry
This is a great plant that will drape over the retaining wall.


To start...
We cut a slit in the landscape fabric for our flowers...



... then used more stakes in-between each flower.


We added wood chips around the BUSHES... not the flowers.


You don't need to add wood chips - but we decided to - mainly because we like how it looks!


Finally...
ADD YOUR ROCK!
We purchased two-inch river rock...


... and scooped it around the bushes and flowers.



As an added BONUS...
We added river rock next to the bottom tier of our retaining wall.


We outlined the river rock with edging blocks...


... and used some larger rocks as accent pieces.


Whew.
FINALLY DONE!


What do you think?


BEFORE


AFTER


BEFORE


AFTER




The house finally has more "curb appeal."

 

It took us one month to complete, but I think the end result is pretty great!



Job well done, Dad!
You deserve a break...

Or maybe not.


We're actually not QUITE done yet.
Can you guess what we're doing to REALLY complete the front of the house?



I'll give you a clue...


Make sure to check back after Labor Day for the FINAL result!


3 comments:

  1. This does look like a great DIY project! Recently we had EP Henry Roxbury come out and add retaining walls in our backyard and we loved them so much we want to add more. It's funny how popular retaining walls in nj are becoming! I think I am going to forward this to my husband so we can get started!

    ReplyDelete
  2. Great project love seeing all the pics. I have one question though, what material do you use to keep the bricks together? I didn't see any mortar or cement.

    ReplyDelete
  3. The retaining walls you showed in these pictures really made a huge difference! It's amazing to see how such a simple change can change the whole look of a home. I've been thinking of putting a retaining wall toward the side of my house because we are located on a hill. I guess I had never considered doing it ourselves, but it seems simple enough. I'll definitely consider the option! http://www.qualitylandscape-fence.com/Landscape-DesignBuild.html

    ReplyDelete